In a previous lesson, I covered the standard access-list, now it’s time to take a look at the extended access-list. This is the topology we’ll use:
Using the extended access-list, we can create far more complex statements. Let’s say we have the following requirement:
- Traffic from network 18.104.22.168 /24 is allowed to connect to the HTTP server on R2, but they are only allowed to connect to IP address 22.214.171.124.
- All other traffic has to be denied.
Now we need to translate this to an extended access-list statement. Basically, they look like this:
[source] + [ source port] to [destination] + [destination port]
Let’s walk through the configuration together:
R2(config)#access-list 100 ? deny Specify packets to reject dynamic Specify a DYNAMIC list of PERMITs or DENYs permit Specify packets to forward remark Access list entry comment
First of all, we need to select a permit or deny. By the way, you can also use a remark. You can use this to add a comment to your access-list statements. I’ll select the permit:
R2(config)#access-list 100 permit ? <0-255> An IP protocol number ahp Authentication Header Protocol eigrp Cisco's EIGRP routing protocol esp Encapsulation Security Payload gre Cisco's GRE tunneling icmp Internet Control Message Protocol igmp Internet Gateway Message Protocol ip Any Internet Protocol ipinip IP in IP tunneling nos KA9Q NOS compatible IP over IP tunneling ospf OSPF routing protocol pcp Payload Compression Protocol pim Protocol Independent Multicast tcp Transmission Control Protocol udp User Datagram Protocol
Now we have a lot more options. Since I want something that permits HTTP traffic we’ll have to select TCP. Let’s continue:
R2(config)#access-list 100 permit tcp ? A.B.C.D Source address any Any source host host A single source host
Now we have to select a source. I can either type in a network address with a wildcard or I can use the any or host keyword. These two keywords are “shortcuts”. Let me explain:
- If you type “0.0.0.0 255.255.255.255,” you have all networks. Instead of typing this, we can use any keyword.
- If you type something like “126.96.36.199 0.0.0.0” we are matching a single IP address. Instead of typing the “0.0.0.0” wildcard, we can use the keyword host.
I want to select network 188.8.131.52 /24 as the source, so this is what we will do:
R2(config)#access-list 100 permit tcp 184.108.40.206 0.0.0.255 ? A.B.C.D Destination address any Any destination host eq Match only packets on a given port number gt Match only packets with a greater port number host A single destination host lt Match only packets with a lower port number neq Match only packets not on a given port number range Match only packets in the range of port numbers
Besides selecting the source, we can also select the source port number. Keep in mind that when I connect from R1 to R2’s HTTP server my source port number will be random so I’m not going to specify a source port number here.
R2(config)#access-list 100 permit tcp 220.127.116.11 0.0.0.255 host 18.104.22.168 ? ack Match on the ACK bit dscp Match packets with given dscp value eq Match only packets on a given port number established Match established connections fin Match on the FIN bit fragments Check non-initial fragments gt Match only packets with a greater port number log Log matches against this entry log-input Log matches against this entry, including input interface lt Match only packets with a lower port number neq Match only packets not on a given port number precedence Match packets with given precedence value psh Match on the PSH bit range Match only packets in the range of port numbers rst Match on the RST bit syn Match on the SYN bit time-range Specify a time-range tos Match packets with given TOS value urg Match on the URG bit <cr>
We will select the destination, which is the IP address 22.214.171.124. I could have typed “126.96.36.199 0.0.0.0,” but it’s easier to use the host keyword. Besides the destination IP address, we can select a destination port number with the eq keyword:
R2(config)#access-list 100 permit tcp 188.8.131.52 0.0.0.255 host 184.108.40.206 eq 80
This will be the end result. Before we apply it to the interface, I will add one useful extra statement: