There are two common protocols for remote management to your Cisco IOS router or switch: telnet and SSH.
Telnet is easy to configure but not used often anymore since it is insecure, everything you do is sent in plaintext while SSH uses encryption. However, some older devices might only support telnet, so it’s good to know how to configure it. Besides remote management, the telnet client is also very useful to test access-lists, routing and if certain ports are listening or not.
In this lesson, I’ll show you everything there is to know about telnet.
For this example we will use the following topology:
R1 will be our telnet server, R2 will be used as a telnet client.
Your router or switch will have a certain amount of VTY lines. These are virtual terminal lines that define how many concurrent connections it supports. Let’s take a look:
R1(config)#line vty 0 ? <1-924> Last Line number <cr>
This router supports more than 900 VTY lines which is a lot. Some smaller boxes will typically have 4 or 16 VTY lines. Let’s configure only the first five VTY lines:
R1(config)#line vty 0 4 R1(config-line)#transport input ? all All protocols lapb-ta LAPB Terminal Adapter lat DEC LAT protocol mop DEC MOP Remote Console Protocol none No protocols pad X.3 PAD rlogin Unix rlogin protocol ssh TCP/IP SSH protocol telnet TCP/IP Telnet protocol udptn UDPTN async via UDP protocol v120 Async over ISDN
This router supports multiple protocols. Above you can see that telnet and SSH are two supported protocols. It is possible to support multiple protocols but let’s configure the router so that it will only support telnet:
R1(config-line)#transport input telnet
The router will now accept telnet connections but without authentication, it’s not going to work. Let’s configure a password:
R1(config-line)#password my_password R1(config-line)#login
The password will be “my_password”. The login command tells the router to check for this password.
Let’s see if it works:
R2#telnet 192.168.12.1 Trying 192.168.12.1 ... Open User Access Verification Password: R1>
Above you can see that I was able to telnet from R2 to R1. Once you see “open” you know that it has successfully established a TCP connection.
Instead of using a single password, it’s also possible to use usernames and passwords that are stored in a local database on the router or switch. Multiple users are able to log in with the same password but it’s easier to see who has accessed your device if you use multiple usernames. Here’s how to do this:
R1(config)#line vty 0 4 R1(config-line)#no password R1(config-line)#login local
We need to use the login local command to tell the router/switch to use the local database for authentication. Let’s create a user account:
R1(config)#username admin password my_password
We now have an admin user with a password. Let’s test this:
R2#telnet 192.168.12.1 Trying 192.168.12.1 ... Open User Access Verification Username: admin Password: R1>
The router now prompts for the username and password.
As I explained before, telnet sends everything in plain text so it is not secure. Let’s take a look at some Wireshark captures of telnet traffic so that you can see this in action. Here is a single telnet packet:
Above you can see a telnet packet from the client to our server. You can see telnet uses TCP destination port 23.
If we want to see the username and password in clear text then we have to look at the entire TCP conversation.
In Wireshark, you can do this by going to Analyze > Follow > TCP Stream:
Now you can see everything that has been transmitted between the client and server:
All client packets are in red, server packets are in blue. Want to try this yourself? You can find the capture files below:
Now you have seen that telnet is insecure but if you still want to use it, it’s probably best to use it with an access-list so that you can at least restrict which devices are allowed to connect to your router or switch. Here’s how to do this:
R1(config)#access-list 1 permit host 192.168.12.2 R1(config)#line vty 0 4 R1(config-line)#access-class 1 in
First we create an access-list that only permits 192.168.12.2 (R2) and then apply it to the VTY lines with the access-class command. Let’s test it:
R2#telnet 192.168.12.1 Trying 192.168.12.1 ... Open
We are still able to connect. Our access-list will show that some packets have matched:
R1#show access-lists Standard IP access list 1 10 permit 192.168.12.2 (2 matches)
That’s all there is to it.
In the previous example I showed you how you can use the telnet client to connect from R2 to R1 but there’s so much more you can use this client for. Take a look at all its options:
R2#telnet 192.168.12.1 ? /debug Enable telnet debugging mode /ipv4 Force use of IP version 4 /ipv6 Force use of IP version 6 /line Enable telnet line mode /noecho Disable local echo /quiet Suppress login/logout messages /route: Enable telnet source route mode /source-interface Specify source interface /stream Enable stream processing /terminal-type Set terminal type <0-65535> Port number bgp Border Gateway Protocol (179) chargen Character generator (19) cmd Remote commands (rcmd, 514) daytime Daytime (13) discard Discard (9) domain Domain Name Service (53) drip Dynamic Routing Information Protocol (3949) echo Echo (7) exec Exec (rsh, 512) finger Finger (79) ftp File Transfer Protocol (21) ftp-data FTP data connections (20) gopher Gopher (70) hostname NIC hostname server (101) ident Ident Protocol (113) irc Internet Relay Chat (194) klogin Kerberos login (543) kshell Kerberos shell (544) login Login (rlogin, 513) lpd Printer service (515) nntp Network News Transport Protocol (119) onep-plain ONEP Cleartext (15001) onep-tls ONEP TLS (15002) pim-auto-rp PIM Auto-RP (496) pop2 Post Office Protocol v2 (109) pop3 Post Office Protocol v3 (110) smtp Simple Mail Transport Protocol (25) sunrpc Sun Remote Procedure Call (111) tacacs TAC Access Control System (49) talk Talk (517) telnet Telnet (23) time Time (37) uucp Unix-to-Unix Copy Program (540) whois Nicname (43) www World Wide Web (HTTP, 80) <cr>
The two most important options are choosing a source interface and selecting a different port number. Using different port numbers is very useful, you can use this to test if certain services are up and running, test if an access-list is working and even if your routing is configured correctly.
Let’s try a simple example. I will have to enable HTTP server on R1:
R1(config)#ip http server
Now we will use telnet to check if the HTTP server is active:
R2#telnet 192.168.12.1 80 Trying 192.168.12.1, 80 ... Open
We are now connected. If you know HTML, you can even try to request some pages:
GET / HTTP/1.0 HTTP/1.1 401 Unauthorized Date: Tue, 12 Jul 2016 10:31:55 GMT Server: cisco-IOS Accept-Ranges: none WWW-Authenticate: Basic realm="level_15_access" 401 Unauthorized [Connection to 192.168.12.1 closed by foreign host]
R1 disconnects me since I am not authorized by the HTTP server but that’s ok, this example proves that the HTTP server is up and running.
We can also use a different source interface for the telnet client. To test this, I’ll have to add another interface and IP address on R2. I’ll create a loopback for this:
R2(config)#int loopback 0 R2(config-if)#ip address 220.127.116.11 255.255.255.255
Let’s make sure R1 knows how to reach this loopback interface:
R1(config)#ip route 18.104.22.168 255.255.255.255 192.168.12.2
And a quick ping to verify our work:
R1#ping 22.214.171.124 Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 126.96.36.199, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 3/4/5 ms
Great, R1 knows how to reach 188.8.131.52.
Remember that we configured an access-list that only permits 192.168.12.2 to connect to R2? We can verify this by specifying another source interface:
R2#telnet 192.168.12.1 /source-interface loopback 0 Trying 192.168.12.1 ... % Connection refused by remote host
We are not allowed to connect because of the access-list on the VTY lines. You can also combine port numbers and a source interface:
R2#telnet 192.168.12.1 80 /source-interface loopback 0 Trying 192.168.12.1, 80 ... Open
As you can see, we are allowed to connect to TCP port 80 and using the loopback interface as our source.
Want to take a look for yourself? Here you will find the final configuration of each device.
hostname R1 ! ip cef ! username admin password 0 my_password ! interface GigabitEthernet0/1 ip address 192.168.12.1 255.255.255.0 ! ip http server ip route 184.108.40.206 255.255.255.255 192.168.12.2 ! access-list 1 permit 192.168.12.2 ! end
hostname R2 ! ip cef ! interface Loopback0 ip address 220.127.116.11 255.255.255.255 ! interface GigabitEthernet0/1 ip address 192.168.12.2 255.255.255.0 ! end
- Telnet can be used for remote management to your Cisco IOS router or switch.
- Telnet sends everything in plain text so it is not secure. It’s better to use SSH instead.
- If you use telnet, it’s best to use an access-list to restrict what devices are allowed to connect.
- The telnet client is a great tool to connect to different ports, test access-lists and/or routing.