By default there is no limit to the number of MAC addresses a switch can learn on an interface and all MAC addresses are allowed. If we want we can change this behavior with port-security. Let’s take a look at the following situation:
In the topology above someone connected a cheap (unmanaged) switch that they brought from home to the FastEthernet 0/1 interface of our Cisco switch. Sometimes people like to bring an extra switch from home to the office. As a result our Cisco switch will learn the MAC address of H1 and H2 on its FastEthernet 0/1 interface.
Of course we don’t want people to bring their own switches and connect it to our network so we want to prevent this from happening. This is how we can do it:
Switch(config)#interface fa0/1 Switch(config-if)#switchport port-security Switch(config-if)#switchport port-security maximum 1
Use the switchport port-security command to enable port-security. I have configured port-security so only one MAC address is allowed. Once the switch sees another MAC address on the interface it will be in violation and something will happen. I’ll show you what happens in a bit…
Besides setting a maximum on the number of MAC addresses we can also use port security to filter MAC addresses. You can use this to only allow certain MAC addresses. In the example above I configured port security so it only allows MAC address aaaa.bbbb.cccc. This is not the MAC address of my computer so it’s perfect to demonstrate a violation.
Switch(config)#interface fa0/1 Switch(config-if)#switchport port-security mac-address aaaa.bbbb.cccc
Use the switchport port-security mac-address command to define the MAC address that you want to allow. Now we’ll generate some traffic to cause a violation:
C:\Documents and Settings\H1>ping 18.104.22.168
I’m pinging to some bogus IP address…there is nothing that has IP address 22.214.171.124; I just want to generate some traffic. Here’s what you will see:
SwitchA# %PM-4-ERR_DISABLE: psecure-violation error detected on Fa0/1, putting Fa0/1 in err-disable state %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0090.cc0e.5023 on port FastEthernet0/1. %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to down %LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to down
We have a security violation and as a result the port goes in err-disable state. As you can see it is now down. Let’s take a closer look at port-security:
Switch#show port-security interface fa0/1 Port Security : Enabled Port Status : Secure-shutdown Violation Mode : Shutdown Aging Time : 0 mins Aging Type : Absolute SecureStatic Address Aging : Disabled Maximum MAC Addresses : 1 Total MAC Addresses : 1 Configured MAC Addresses : 1 Sticky MAC Addresses : 0 Last Source Address:Vlan : 0090.cc0e.5023:1 Security Violation Count : 1
Here is a useful command to check your port security configuration. Use show port-security interface to see the port security details per interface. You can see the violation mode is shutdown and that the last violation was caused by MAC address 0090.cc0e.5023 (H1).
Switch#show interfaces fa0/1 FastEthernet0/1 is down, line protocol is down (err-disabled)
Shutting the interface after a security violation is a good idea (security-wise) but the problem is that the interface will stay in err-disable state. This probably means another call to the helpdesk and you bringing the interface back to the land of the living! Let’s activate it again:
Switch(config)#interface fa0/1 Switch(config-if)#shutdown Switch(config-if)#no shutdown
To get the interface out of err-disable state you need to type “shutdown” followed by “no shutdown”. Only typing “no shutdown” is not enough!
It might be easier if the interface could recover itself after a certain time. You can enable this with the following command: