IPv6 OSPFv3 on Cisco IOS Router

When we use OSPF for IPv4 we are using OSPFv2. OSPF has been updated for IPv6 and is now called OSPFv3. These are two different routing protocols and in this lesson I’ll show you how to configure OSPFv3 so that you can route IPv6 traffic. Here’s the topology we’ll use:

ipv6 routing two routers

 

Let’s start with the configuration of the interfaces and the IPv6 addresses. We don’t have to configure any global unicast IPv6 addresses on the FastEthernet interfaces because OSPFv3 uses link-local addresses for the neighbor adjacency and sending LSAs. Here’s the configuration:

R1(config)#ipv6 unicast-routing 
R1(config)#interface loopback 0
R1(config-if)#ipv6 address 2001::1/128
R2(config)#ipv6 unicast-routing 
R2(config)#interface loopback 0
R2(config-if)#ipv6 address 2001::2/128

Don’t forget to enable IPv6 unicast routing otherwise, no routing protocol will work for IPv6. Let’s check the interfaces:

R1#show ipv6 interface brief 
FastEthernet0/0            [up/up]
Loopback0                  [up/up]
    FE80::CE09:18FF:FE0E:0
    2001::1
R2#show ipv6 interface brief 
FastEthernet0/0            [up/up]
Loopback0                  [up/up]
    FE80::CE0A:18FF:FE0E:0
    2001::2

After configuring the IPv6 addresses on the loopback interface, you can see the global unicast and the link-local IPv6 addresses. There is no link-local address on the FastEthernet interfaces, however, so we’ll have to fix this:

R1(config)#interface fastEthernet 0/0
R1(config-if)#ipv6 enable
R2(config)#interface fastEthernet 0/0
R2(config-if)#ipv6 enable
R1#show ipv6 interface brief 
FastEthernet0/0            [up/up]
    FE80::CE09:18FF:FE0E:0
Loopback0                  [up/up]
    FE80::CE09:18FF:FE0E:0
    2001::1
R2#show ipv6 interface brief 
FastEthernet0/0            [up/up]
    FE80::CE0A:18FF:FE0E:0
Loopback0                  [up/up]
    FE80::CE0A:18FF:FE0E:0
    2001::2

Now we can configure OSPFv3:

We're Sorry, Full Content Access is for Members Only...

If you like to keep on reading, Become a Member Now!

  • Learn any CCNA, CCNP and CCIE R&S Topic. Explained As Simple As Possible.
  • Try for Just $1. The Best Dollar You’ve Ever Spent on Your Cisco Career!
  • Full Access to our 800 Lessons. More Lessons Added Every Week!
  • Content created by Rene Molenaar (CCIE #41726)
518 Sign Ups in the last 30 days
satisfaction-guaranteed

  • 100% Satisfaction Guaranteed!
  • You may cancel your monthly membership at any time.
  • No Questions Asked!

Tags:


Forum Replies

  1. Hi Rene,
    Do areas work the same way ON IPV6 as on OSPF v2?

  2. Hi Alfredo,

    The areas are still the same, basically OSPFv2 and OSPFv3 operate in the same way but there are some differences when it comes to LSAs, building the LSDB, addressing, etc.

    I’ll cover this in another lesson if you are interested.

    Rene

  3. Hey,
    Why we use global Unicast address? isn’t it public address? I understand when its local communication we can get away with link local address and when we require routing we use Global Unicast or Unique local, right? Can we use unique local address in above example instead of Global unicast? implied we are not going to route outside it is just going to be site and inter-site based routing, so in that case we can use Unique local?

    Thanks,
    AD

  4. Also, please show how to assign a unique local address?

    Thanks,

32 more replies! Ask a question or join the discussion by visiting our Community Forum